iFlight Chimera7 320mm 7inch 6S FPV LR Analog BNF with RaceCam R1 Mini 1200TVL 2.1mm Cam/Xing 2806.5 1300KV/1800KV Motor for | Электроника

iFlight Chimera7 320mm 7inch 6S FPV LR Analog BNF with RaceCam R1 Mini 1200TVL 2.1mm Cam/Xing 2806.5 1300KV/1800KV Motor for | Электроника

Description：

Introducing what has been requested for too long already! A super efficient iFlight 7inch Long-Range bird that can go where you couldn't go before and can carry bigger batteries to get the flight time to surf the swiss alps if you want! Super stiff frame for minimum resonance and 2806.5 motors for maximum 7inch prop control. Fly big batteries top-mounted, or even bigger batteries bottom-mounted, 6cells recommended or 5cells for slow cruising. But whatever style you fly, a Lipo or Lion pack will just do the job. Recommended 5S 3.000mAh above (slow cruising) or 6S 2.500mAh above.

GPS functionality to find your way back and Betaflight GPS Rescue mode ready to setup (default OFF to prevent unexpected behaviour; Setup instructions included). Vertical and horizontal TBS Crossfire antenna mounts included to cover you and your antenna dead ends just in case. GoPro universal TPU bottom stand included; fits your original GoPro bracket and our TPU GoPro protectors (additional).

Tips:

VTX is set to 25mW by default! Power levels above 25mW require a HAM license or have to be approved by local authorities! Please ensure you're flying legal frequencies and use our prepared Betaflight VTX tables according to your region.

HIGHLIGHTS:

6mm rigid arm design for more stiffness

Top- and bottom battery mount option

XING 2806.5 efficient wide stator motors

GPS pre-installed for more safety at distance

800mW high power adjustable VTX

GoPro TPU bottom stand (GoPro protector not included)

360° TPU protection, FPV cam protection and antenna mounts

Battery voltage LED status light (illuminated IF logo on the bottom)

PRE-TUNED & PRE-SETUP:

Is this your first BNF or are you just starting through with FPV? This article might probably help:General Guide // iFlight BNF

Don't worry about tuning, we did that for you already! A basic PID- and Filter tuning was applied for a great flight experience!

To restore lost tunes or updates, please check our linked article on"Firmware/Factory Dumps"

Angle-Mode (self balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess!

Please check our linked article on"How to disable Angle-Mode, activate Acro-Mode"

GPS Rescue is OFF by default to prevent from unwanted or unexpected drone behaviour.

Please check our linked article on"GPS Rescue Mode // Setup"

FRAME //: Chimera7

Wheelbase: 320mm

Main body dimension: 258*199mm

Bottom to top distance: 20mm

Arm thickness: 6mm

Bottom plate thickness: 3mm

Top plate thickness: 2mm

Upper(middle) plate thickness: 3mm

Camera plate thickness: 3mm (included TPU inserts)

ELECTRONICS // SucceX-D F7 V2.2 Stack (50A 4-in-1 ESC)：

SucceX-D F7 V2.2 TwinG

MCU: STM32 F722

Gyro：2xICM20689

Baro: No

Blackbox：32MB

Betaflight OSD: YES

BEC: 5V 2.5A / 9V 2.5A

Current sensor scale:  100

Inverter for SBUS input (UART2-RX)

Smartaudio & Tramp VTX protocol supported

Beeper pad : Yes

RSSI input pad: No

UARTs：5

Motor outputs: 8

8 pin 4in1 ESC port (GND, VBAT, M1, M2, M3, M4, CUR, R5)

BLHeli32 Telemetry：RX5

Input voltage：recommended 2-6S, MAX 8S

Firmware Target:   IFLIGHT_F722_TWING

Mounting pattern: 30.5*30.5mm φ4mm with Grommets φ3mm

Dimensions:   36*36mm

Weight: 7.5g

USB type-C

ESC // SucceX 50A

MCU: STM32F051

Up tp 48kHz PWM frequency

Capacitance: 470uF/50V

Current Sensor: Yes

Input: 2-6S LIPO

Constant: 50A / Burst: 60A

BlHeli32 telemetry: Yes

BEC: No

Supports up to Dshot1200, Proshot, Oneshot, Multishot

Target: iFlight-BL32-4IN1

Weight: 14.4g

Mounting pattern: 30.5*30.5mm/Φ3mm

Dimensions: 43*39mm (including the power pads)

VTX// SucceX Force 5.8g 800mW VTX Adjustable

Item: SucceX-Force 800mW adjustable VTX

Input voltage: 7-36V

Output voltage/ Max current: 5V 1A

12V input current: 40mA@PIT MODE, 95mA@25mW, 185mA@200mW，250mA@500mW, 380mA@800mW

Channel: 40

size:36*36*3mm

PIT/25mW/200mW/400mW/800mW

Prebuilt and indoor tested Quadcopter

1x Chimera7 frame

1x GoPro TPU bottom stand incl. lock screw

1x RaceCam R1 Mini 1200TVL 2.1mm 19*19

1x Albatross RHCP SMA 5.8g 150mm antenna

2 sets x Gemfan tri-blade 7040 props (Set of 4 - Color may vary)

4x 20*250mm Microfiber PU Leather Battery Strap (Color May Vary)

Additional Suggested Parts (not included)

Adjustable Gopro mount（0-40）

1300KV  Cruiser, suggested battery: 6S 4000mAh

1800KV Speed Cruiser, suggested battery: 6S 2600mAh