Комплект солнечных батарей 50 Вт 100 150 гибкий модуль фотоэлектрический контроллер

Комплект солнечных батарей 50 Вт 100 150 гибкий модуль фотоэлектрический контроллер

Solar Panel kit 50 watt Flexible Module Cell 100W 150W Photovoltaic Charge Controller For Car mobile home boat 12V batteries

solar panel Specification

Maximum power(Pmax) 50W

Output tolerance ± 3%

Maximum system voltage 700V DC

Open circuit voltage(Voc) 19.2V

Short circuit current(Isc) 3.43A

Maximum power voltage(Vmp) 16V

Maximum power current(Imp) 3.15A

Cell efficiency 21%

Operating temperature（NOCT） 45±2℃

Temperature range -40℃～+80℃

Number of cells 32pcs

Weight 1030g

Size 1060*277*2.5 mm

Standard Test Conditions ： lrradiance 1000w/m^2，Temperature 25℃, AM=1.5

Packing list

1* 50W Flexible Solar Panel (1060*277MM)

OR

2* 50W Flexible Solar Panel (1060*277MM)

OR

3* 50W Flexible Solar Panel (1060*277MM)

OR

1*50w solar panels (1060*277MM)
1 set 3m cable with PV connector
1 set 3m cable with Alligator clip
1*10A Controller

OR

2*50w solar panels (1060*277MM)
1 set 3m cable with PV connector
1 set 3m cable with Alligator clip
1*10A Controller
1 set 2 in 1 adapter

OR

3*50w solar panels (1060*277MM)
1 set 3m cable with PV connector
1 set 3m cable with Alligator clip
1*20A Controller
1 set 3 in 1 adapter

【Semi-flexible】 Can have a bending angle of up to 30 degrees. Can be used on a wide variety of irregular surfaces.
【High efficiency】 Made of highly efficient single crystal silicon, the efficiency is up to 21%. More compact size generate 30% more energy than market solar module, steady perfect energy generate power.
【Durable】 resistance to resistance, can withstand different environment, waterproof performance is good.
【Portable】 The thickness is only 3 mm, light weight, easy carrying, easy shipping, easy installation.
【Widely Applications】 It is widely used to put golf car, yacht, boat, caravan, electric car, travel tourism car, patrol car, roof top, camping, roof power generators, tent, portable bag, backpacks, portable generator kits, etc. Charge for 12V Battery, fix the problem that the device cannot start due to lack of power.

Off-Grid Solar System User Manual

Use attention
1. Please install the solar panel system in cloudy days. If installing in strong light, pay attention to protection against electric shock.
2. Normally red color is the positive electrode and black color is the negative electrode. The positive and negative electrodes must be installed correctly.
Do not directly connect the positive and negative poles of the solar panel to avoid short circuit.
3. Do not scratch or step on the solar panel during installation and use. Check in advance whether the controller, battery, inverter and other accessories are normal.

Installation process
1. First connect the battery to the controller to activate the controller. There is no display if only the solar panel is connected to the controller.
2. Then connect the solar panels, please install solar modules in a sunny and shadowless area. When using a 12V system, configuring 12V batteries and 16V/18V solar panels, so multiple solar panels need to be connected in parallel. When using a 24V system, configuring 24V batteries and 32V/36V solar panels, so every 2 solar panels need to be connected in series, then connect all pairs in parallel. And so on. The parallel requires the same voltage, especially the series requires the same current.
The schematic diagrams of parallel and series connection of solar panels are as follows
(the same applies to batteries):

Next, connect the inverter to the battery, and finally connect the load to the inverter. The low-power DC load can be directly connected to the controller, and the AC load needs to be connected to the inverter.
First connect the inverter wire to the positive and negative poles of the inverter and tighten them, and then connect the other end of the wire to the positive and negative poles of the battery. It is normal if there is a small spark. Then connect the load to the inverter and turn on the inverter switch to start the load.
Do not connect the inverter to the controller to avoid damage.

The whole connection diagram is as follow: