Сохраните в закладки:
*История изменения цены! Указанная стоимость возможно, уже изменилось. Проверить текущую цену - >
| Месяц | Минимальная цена | Макс. стоимость | Цена |
|---|---|---|---|
| Feb-17-2026 | 1043.83 руб. | 1064.10 руб. | 1053.5 руб. |
| Jan-17-2026 | 846.69 руб. | 863.9 руб. | 854.5 руб. |
| Dec-17-2025 | 1026.61 руб. | 1047.65 руб. | 1036.5 руб. |
| Nov-17-2025 | 1018.54 руб. | 1038.69 руб. | 1028 руб. |
| Oct-17-2025 | 813.27 руб. | 829.20 руб. | 821 руб. |
| Sep-17-2025 | 1002.58 руб. | 1022.14 руб. | 1012 руб. |
| Aug-17-2025 | 993.66 руб. | 1013.27 руб. | 1003 руб. |
| Jul-17-2025 | 985.2 руб. | 1005.22 руб. | 995 руб. |
Новые товары
Характеристики
Описание товара
DC 0-20A Hall Sensor Current Meter LED Digital Hall Amp Panl Meter DC Ammeter Power Supply DC 4-30V Current Meter Red Digits
1.Include a current transformer, no need to buy it separately.
2.Please try not to install the meter and current transformer around the high temperature, strong magnetic field
and large transformer, otherwise the accuracy will be affected.
3.In order to obtain a higher precision measurement, it is recommended to "preheat for 5 minutes" before
adjusting the calibration.
4.Since the 24V battery charge full of floating voltage may be over 30V, so "no" recommended direct use it.
5.When you select range, not the larger the better. the larger the range, the larger the error, it is recommended
that it is 1.5 or 2 times as large as the actual test value.
6.This meter and CT have been calibrated by the "one to one". Please don't mix it up when you use it in the later period. If mixed, you need to recalibrate it.
The relative error between the instrument and the instrument, or after long-term use, due to component aging or environmental temperature changes caused by the error can be calibrated by the following methods, in order to get more accurate measurements, it is recommended to energize and then preheat more than 5 minutes before recalibration. Current calibration: In the condition of without current, use a screwdriver to adjust the "zero(or 0)" potentiometer that behind the transforme until the decimal point of the ammeter flashes fast to the best; always bright or no light shows positive current, slow flashing shows negative current In the condition of the half of actual measured current value , adjust the "amplitude modulation(or A)" potentiometer by the side of the transformer until it is consistent with the standard meter. If the test accuracy is very high, you can repeat the above two steps to get higher accuracy.


Эти очки в смотрятся стильно и привлекательно, отлично подчеркивая мой имидж. Выполнены в стиле ретро. Учитывая мою любовь к таким... Читать отзыв полностью...
Понравилась рубашка и решил заказать. Пришла доставка за четыре месяца после оплаты товара, конечно, долго. По качеству нормальная вещь, а... Читать отзыв полностью...
Спасибо за такую милоту!!! Заказывала у вас двум сестренкам на день рождения! Они были в восторге! В магазинах ни где... Читать отзыв полностью...
Скоро зимние праздники наступят и я нахожусь в поисках подарков моей жене... Думаю, что эта сумочка моей жене должна понравиться.... Читать отзыв полностью...
Не раз заказывала одежду себе и детям с этого сайта, всё приходит вовремя, без задержек. Размеры всегда уточняются, ещё не... Читать отзыв полностью...
Подала заявку на сайте на заказ постельного белья цвета шампанского. В этот же день начали исполнять мой индивидуальный заказ. Через... Читать отзыв полностью...
Supply voltage:DC4-30V(Note:The maximum input voltage can not exceed 30V, or be burnt.)
Operating current:<30mA
Test current:DC0-20A
Display type:0.52'' LED
Measurement rate:≥ 500mS / time
Measurement accuracy:1% (± 2 digits)
CT wire length:150mm
Terminal wire length:150mm
Dimension:54*30*21mm
Mounting hole:47.2*27.3mm
1. The wide power supply range, with reverse polarity protection.
2 .Use the SMT technology,so consistency is very good.
3.With a current calibration potentiometer, you can calibrate by yourself. The tolarance is absolutely exit.
4 .CT adopts the design of perforation type wire through the hole,without having to cut wires, without damage, without changing the original electric current wire can be achieved current measurements.
5 .Since CT and measured wire is isolated completely, this meter can be measured the current of the power positive, negative and any devices, don't need to worry about the ammeter "common ground".
6 .The positive and negative current can be measured, and the "positive" current is shown in the positive direction (the decimal point is always bright or not bright), and the "negative" current is shown in the reverse direction(the decimal point flashes slowly.
7.The pressure tolerance between the measured wires is as high as: 2KV.
8 .High reliability, high resistance to current shock, no current impact damage ammeter.
9 .With two wires,connection is convenient,easy connect to solar system/car/electric vehicle/motorcycle interior wires.It is used to monitor the battery voltage and can be also used for other products.
Наконец то я приобрела очки, о которых давно мечтала. Спасибо продавцу. Цена радует меня. Качество очень хорошее. На лето... Читать отзыв полностью...